Insect Light Trap Replacement Glueboards with Dual Adhesive Layers

Insect Light Trap Replacement Glueboards with Dual Adhesive Layers 

Insect light trap replacement glueboards are five layer sandwich construction – cardboard base, a coat of adhesive, a silicone release liner, then another adhesive layer, and a second liner. You peel off the first release paper to expose the working glue. When that surface gets saturated with flies, mosquitoes, or other flying insects, you don’t rush for a replacement. Just strip away the second liner, and the board is fresh again.Here’s the practical difference: most glueboards for insect light traps give you a single sticky layer. Once it’s covered with bugs, you toss it and install a new one. Ours work differently.

That simple step gives you roughly double the service life compared to conventional single‑layer boards. In busy kitchens or food plants where traps fill up fast, this means fewer trips up the ladder, less downtime, and lower costs per catching cycle. We’ve also tweaked the adhesive to resist hardening under continuous UV light – a known weakness in cheaper alternatives. The cardboard stays flat even in humid conditions, so the whole glue face stays fully exposed to incoming pests. And if you’re keeping pest logs for audits, the printed grid on the surface helps you count and identify species without removing them from the glue.

TECHNICAL SPECIFICATIONS

• Construction :Cardstock + Glue + Release paper + Glue + Release paper (5 layers)
• Usable adhesive layers: 2 (sequential)
• Standard dimensions :425 x 245mm
• Adhesive type :UV‑stable, non‑drying, solvent‑free
• Release liner: Silicone‑coated, easy peel
• Grid pattern :Printed for monitoring and counting
• Shelf life: 2 years unopened

KEY FEATURES

• Two adhesive rounds per board – use the first side, then peel to expose the second. No extra board needed mid‑cycle.
• UV‑resistant glue stays tacky week after week, even under bright lamps.
• Warp‑resistant backing – stays flat in steamy dishwashing areas or cool storage rooms.
• Clean peel release liners – no tearing, no sticky residue on your fingers.
• Counting grid printed directly on the board – helps with pest trend logs without extra tools.
• Non‑toxic adhesive – safe around food prep zones, no chemical attractants added.

PACKING & SHIPPING

• Retail pack: 2 boards per opp bag
• Bulk case: 200 boards  per master carton.
• Pallet: 40 cartons per pallet, stretch‑wrapped.
• Shipping: as customer’s requirement

HOW TO USE

1. Switch off the trap and let the bulbs cool.
2. Remove the old board.
3. Peel away only the first release liner – leave the second one intact.
4. Insert the board with the exposed glue facing the light source.
5. When that layer is full (flies covering most of the surface), take the board out.
6. Peel off the second liner to reveal the fresh glue underneath.
7. Put the same board back in – it’s ready for another full catching period.
8. Replace entirely only after the second layer is spent.

APPLICATIONS

Commercial kitchens, restaurant back‑of‑house, food processing lines, warehouses, hospital cafeterias, hotel loading docks, supermarket bakeries, school canteens, and any facility that runs insect light traps as part of their pest management plan.

CUSTOMIZATION OPTIONS

• Non‑standard dimensions for older or less common trap models.
• White or black cardstock (black often blends better in darker fixtures).
• Plain surface (no grid) if you prefer.
• Private label packaging with your own branding.
• Alternative adhesive tack levels – we can dial it up for heavy fly pressure or down for delicate moth counts.

FAQs

Q: Are Insect light trap replacement glueboards just a double‑sided board?

No. Double‑sided boards stick bugs on both faces at the same time, but once either side is full, the whole thing is done. Our layers are sequential – you use one side, finish it, then expose the next. That gives you full capacity from each layer, not half‑used leftovers.

Q: How long does each layer last?

That depends on pest activity. In a moderate environment, expect 4–6 weeks per layer. In heavy infestations, it fills faster – but then you’re glad you have a backup layer ready without fetching a new board.

Q: Will the glue dry out under the UV lamp?

We’ve added UV stabilisers to prevent skinning. It stays sticky until it’s physically covered with insects – not before.

WHY CHOOSE US

Insect light trap replacement glueboards are special design for certain customers,  we don’t just copy what’s already out there. The dual‑layer idea came directly from facility managers who were tired of changing boards every week. We listened, tested, and delivered a solution that cuts replacement frequency in half without cutting corners on stickiness or durability.